RC Power Supply 1200W

Compact and powerful, it comes with an AC port and 3 bullets ouput to provide maximum connectivity for chargers and other accessories.
It includes a protection plate to keep outputs safe from damage or breakage.

Specifications:
Input: AC 100/240V
Output: 1200W 100A
Size: 1.5 x 3.5 x 7.75″

Free shipping in USA.

RC Power Supply 1200W

Junsi iCharger 406DUO

Specifications:
Net weight: 0.91kg
Dimension: 171×118×59 ±0.5mm
Input Voltage Range: 10.0—30.0VDC
Maximum Input Current Limit: <60A, CH1/2<47A Maximum Charge/Discharge Current: 70A in sync mode, 40A in async mode Maximum Charge Power Capacity: 1400W (Channel 1000W @input > 23.5V)
Maximum Discharge Power Capacity: 140W (Channel 80W)
Maximum Regenerative Discharge Power Capacity: 1400W (Channel 1000W)
Maximum Extra Discharge Power Capacity: 2000W (Channel 1000W @25V/40A)
Maximum Current Drain for Balancing: 2.4A in sync mode, 1.2A in async mode
USB Charging Port: 5V/1A(current-limiting protection 1.2A)

Charger Junsi iCharger 406DUO

Lilo/LiPo/Life/NiMH/NiCD DC Battery Charger (6S/40A/1400W)

2 Versions available

  1. Junsi iCharger 406DUO
  2. Charger with Power Supply 750W
Version:

Flat Skid Plate for Axial SCX10 & SCX10 II

The Flat Skid Plate is the perfect addition to your Crawler SCX10, SCX10 II RTR, or other custom builds. This Skid Plate has been optimized to increase ground clearance compared to the stock Axial Skid Plate. The Skid Plate is perfectly flat and does not hang below the chassis rails like the stock Axial Skid Plate.

Features: Flat Skid Plate -8mm. 4 screws are included.

Compatible with: SCX10 and SCX10 II RTR

Free shipping in USA.

Flat Skid Plate for SCX10

Discharge Bank 40 Amp 1S to 4S

  • Resistor Bank for iCharger DUO
  • Discharge at 40A your lipos 1S to 4S
  • Does not heat up thanks to its box enclosure
  • Save room and time: no need for a resistor stand
  • Ready to use: plug easily to your iCharger
  • Clean and neat design with short wires
  • Optimize space with our charger stand
Free shipping in USA.

More information here.

Resistor Bank for iCharger
Stand:

Regenerative Discharger for iCharger DUO

  • Discharges your lipos from 1S to 4S at 40A
  • Recovers energy while discharging to re-use it for charging
  • Is a great deal: does the job of 2 resistor banks with 2 iCharger DUO
  • Does not block a charger output: allows you to use 2 outputs at the same time
  • Is ready to use: plugs easily to your iCharger
  • Has a clean and neat design with short wires
  • Optimizes space with our stand for charger and power supply
  • Uses the Cycle mode on your iCharger X6

Free shipping in USA.

More information here.

Regenerative Discharger
Stand:

RC Power Supply 750W

Compact and powerful, it comes with an AC port and 3 bullets ouput to provide maximum connectivity for chargers and other accessories.
It includes a protection plate to keep outputs safe from damage or breakage.

Specifications:
Input: AC 100/240V
Output: 750W 62.5A
Size: 1.5 x 3.5 x 7.75″

Free shipping in USA.

RC Power Supply 750W

Charger Stand For iCharger 406DUO

Charger Stand For iCharger 406DUO

This Charger Stand was developed to allow you to mount a Junsi iCharger 406DUO chargers on top of your Power Supply. With our Charger Stand, no problem of balance. This charger stand is small, perfect for traveling.

* Power supply recommended Width 8.6in (218mm), Depth 3.5in (89mm)and  Height 1.5in  (38mm)
** Power supply shown for reference only. Power supply is not included with the charger stand.

Free shipping in USA.

Charger Stand iCharger 406DUO

Charger Stand For iCharger 4010DUO

Charger Stand For iCharger 4010DUO

This Charger Stand was developed to allow you to mount a Junsi iCharger 4010DUO chargers on top of your Power Supply. With our Charger Stand, no problem of balance. This charger stand is small, perfect for traveling.

* Power supply recommended Width 8.6in (218mm), Depth 3.5in (89mm)and  Height 1.5in  (38mm)
** Power supply shown for reference only. Power supply is not included with the charger stand.

Free shipping in USA.

Charger Stand iCharger 4010DUO

Charger Stand For iCharger 308DUO

Charger Stand For iCharger 308DUO

This Charger Stand was developed to allow you to mount a Junsi iCharger 308DUO chargers on top of your Power Supply. With our Charger Stand, no problem of balance. This charger stand is small, perfect for traveling.

* Power supply recommended Width 8.6in (218mm), Depth 3.5in (89mm)and  Height 1.5in  (38mm)
** Power supply shown for reference only. Power supply is not included with the charger stand.

Free shipping in USA.

Charger Stand iCharger 308DUO

Shock Stand Traxxas X-maxx

The Shock Stand is a nice addition for your tool box. The first Shock Stand for your Traxxas Xmaxx.

This stand features a twin deck design. The shock stand is used to hold shock of 26mm diameter, making it compatible with a variety of RC shock types. 

We can make a special size for you. Thanks for contacting us.

Free shipping in USA.

Shock Stand Traxxas Xmaxx