40 Amp Discharge Resistor Bank 1S to 4S

  • Resistor Bank for iCharger DUO
  • Discharge at 40A your lipos 1S to 4S
  • Does not heat up thanks to its box enclosure
  • Save room and time: no need for a resistor stand
  • Ready to use: plug easily to your iCharger
  • Clean and neat design with short wires
  • Optimize space with our charger stand
Free shipping in USA. Ship within 1 week.

More information here.

Resistor Bank for iCharger
Stand:

Regenerative Discharger for iCharger DUO

  • Discharges your lipos from 1S to 4S at 40A
  • Recovers energy while discharging to re-use it for charging
  • Is a great deal: does the job of 2 resistor banks with 2 iCharger DUO
  • Does not block a charger output: allows you to use 2 outputs at the same time
  • Is ready to use: plugs easily to your iCharger
  • Has a clean and neat design with short wires
  • Optimizes space with our stand for charger and power supply
  • Uses the Cycle mode on your iCharger X6

Free shipping in USA. Ship within 1 week.

More information here.

Regenerative Discharger
Stand:

RC Power Supply 750W

Compact and powerful, it comes with an AC port and 3 bullets ouput to provide maximum connectivity for chargers and other accessories.
It includes a protection plate to keep outputs safe from damage or breakage.

Specifications:
Input: AC 100/240V
Output: 750W 62.5A
Size: 1.5 x 3.5 x 7.75″

Free shipping in USA.

RC Power Supply 750W

Charger Stand For iCharger 406DUO

Charger Stand For iCharger 406DUO

This Charger Stand was developed to allow you to mount a Junsi iCharger 406DUO chargers on top of your Power Supply. With our Charger Stand, no problem of balance. This charger stand is small, perfect for traveling.

* Power supply recommended Width 8.6in (218mm), Depth 3.5in (89mm)and  Height 1.5in  (38mm)
** Power supply shown for reference only. Power supply is not included with the charger stand.

Free shipping in USA.

Charger Stand iCharger 406DUO

Charger Stand For iCharger 4010DUO

Charger Stand For iCharger 4010DUO

This Charger Stand was developed to allow you to mount a Junsi iCharger 4010DUO chargers on top of your Power Supply. With our Charger Stand, no problem of balance. This charger stand is small, perfect for traveling.

* Power supply recommended Width 8.6in (218mm), Depth 3.5in (89mm)and  Height 1.5in  (38mm)
** Power supply shown for reference only. Power supply is not included with the charger stand.

Free shipping in USA.

Charger Stand iCharger 4010DUO

Charger Stand For iCharger 308DUO

Charger Stand For iCharger 308DUO

This Charger Stand was developed to allow you to mount a Junsi iCharger 308DUO chargers on top of your Power Supply. With our Charger Stand, no problem of balance. This charger stand is small, perfect for traveling.

* Power supply recommended Width 8.6in (218mm), Depth 3.5in (89mm)and  Height 1.5in  (38mm)
** Power supply shown for reference only. Power supply is not included with the charger stand.

Free shipping in USA.

Charger Stand iCharger 308DUO

RC XT60 Charge Cable

Charge Cable 2S w/4mm & 5mm Bullet Connector 2′

This RC Charge Cable is assembled with the stepped 4/5mm bullets.

This charge cable uses 10 gauge wires recommended for charge or discharge at 40A wrapped in nylon mesh, plus stepped bullets so you can charge both 4mm and 5mm batteries and XT60 connector on the charger side.

Free shipping in USA.

RC Charge Cable XT60

RC Charge Cable

Charge Cable 2S w/4mm & 5mm Bullet Connector 2′

This RC Charge Cable is assembled with the stepped 4/5mm bullets.

This charger cable uses 10 gauge wires recommended for charge or discharge at 40A wrapped in nylon mesh, plus stepped bullets so you can charge both 4mm and 5mm batteries and 4mm bullets connector on the charger side.

Free shipping in USA.

RC Charge Cable